A dent doesn't care whether it lands on a car door or a piece of artwork. When a 24-inch steel water fountain globe showed up at our shop in Bloomington with a 5-inch dent in it, the owner had one question: could it be saved, or did the whole piece have to be replaced?
The globe belongs to Modern Artifacts, an art company based here in Bloomington, Minnesota, and Bob brought it to us hoping Paintless Dent Repair could do for a decorative water feature what it does for a fender. This was no everyday call. The sphere is built from a thicker gauge steel than any car panel, the basecoat is powder coated, and the butterflies across it were airbrushed on by hand. Nobody could say how it got dented.
Key Takeaways
-
THE CHALLENGE
A 5-inch dent sat in a sealed 24-inch steel globe with no access to the backside and hand-airbrushed artwork on the surface.
-
THE REPAIR
We worked the dent entirely from the outside using a combination of cold glue and hot glue, then used a blending hammer to knock down the crowns of displaced metal.
-
THE RESULT
A 90% to 95% repair in roughly an hour and a half, with the airbrushed butterflies still intact.
Replacing a one-off decorative piece is expensive, and the art company that built the globe was looking for a cost-effective fix instead. PDR made sense here for the same reason it makes sense on a car: the finish stays where it is, and there's no repainting involved. The catch was access. With a sealed sphere, there's no reaching a tool behind the damage, so everything had to be done from the exterior with glue.
Project Summary
| Client Profile: |
Modern Artifacts, an art company (contact: Bob) |
| Project Location: |
Bloomington, Minnesota — Twin Cities metro |
| Primary Objective: |
Save a dented 24-inch steel water fountain globe with Paintless Dent Removal rather than replace the piece. |
| Repair Method: |
Exterior glue pulling with hot and cold glue plus a blending hammer, following the same inspect-quote-access-repair steps as Our Repair Process. |
| Key Outcome: |
90% to 95% of the dent removed in about 90 minutes, with the airbrushed butterflies undamaged |
Sealed Steel Globe, Zero Access
The first look told us most of what we needed to know. The dent measured about 5 inches across on a sphere that's sealed up as a water feature, so there was no panel edge, no drain hole, and no opening to slide a rod through. That ruled out pushing the metal from behind, which is how the majority of our repairs get done.
The finish raised the stakes. A powder-coated basecoat with airbrushed butterflies over the top isn't something anyone can repaint and match, which meant a conventional body shop route would have cost the piece its artwork. We told Bob up front that glue pulling on a hand-airbrushed surface carries a real risk of lifting some of that art, and let him decide how to move forward.
Glue Pulling From the Outside
Glue pulling is the method we reach for whenever the backside of a dent is closed off. We set tabs on the surface with glue, let it cure, and lift the metal from the exterior — on this globe we used a combination of cold glue and hot glue, since the thicker gauge steel responds differently than a car panel does. Between pulls, a blending hammer brought down the crowns of displaced metal ringing the dent so the center could keep flowing back out.
★★★★★
"Had some damage and was concerned PDR couldn't fix. Chopper assured me it wouldn't be a problem. Great communication, work preformed on time and looks great!" — Rocky
We bid the job at a 90% to 95% repair rate, and told Bob that if we couldn't hit it, he wouldn't be charged. That's the same honest framing we use on vehicles, and it's why we take the time to walk a customer through the likely end result before any glue goes on. Odd-shaped metal is familiar ground for us — we do the same kind of work on Boat Dent Repair and Aircraft Dent Repair, and you can see more finished examples in our Before & After Gallery.
90 Minutes, Artwork Intact
The repair came in at the rate we bid: 90% to 95% of the dent lifted back out of the sphere, done in about an hour and a half. The airbrushed butterflies survived every pull, which was the part nobody could guarantee walking in.
Approximate cost on the repair was $350 — a fraction of what building a replacement globe would have run the art company, and no waiting on a new piece to be fabricated. Over the years we've taken on a handful of unusual art repairs, and we've had more success than failures. It's a nice break from the day-to-day, and a good reminder that a dent doesn't always arrive on four wheels.
Dent on Something Unusual?
We've been removing dents in the Twin Cities since 2007, and not all of them come in on a car. Sculptures, fountains, metal fixtures, boats, aircraft — if it's metal and the finish is sound, there's a good chance we can lift it back out without repainting anything.
Have a piece in Bloomington or anywhere in the metro that you're not sure is fixable? Send us a photo or stop by the shop and we'll give you an honest read on it, free.
Frequently Asked Questions
Can paintless dent repair fix a dent with no access behind it in Bloomington?
Yes, in many cases. When we can't get a tool to the backside of a dent to push it, we use glue pulling instead — hot glue and plastic tabs applied to the outside, then lifted from the exterior. That's exactly how we handled the sealed steel fountain globe for a Bloomington art company, and it's the same method we use on closed roof rails and double-walled panels on vehicles.
Will glue pulling damage paint, powder coating, or artwork?
On factory paint it's very rarely an issue. On surfaces that have been repainted or finished by hand, the risk goes up, so we have that conversation with you before anything starts and let you decide how to move forward. On this globe, we warned the customer that the airbrushed butterflies could potentially lift — they came through the repair intact.
What does a dent repair on a metal sculpture or fixture cost?
Every repair is different, so there's no one-size-fits-all price. We look at the time involved, the difficulty of the damage, and where on the piece it sits. The approximate price on this 5-inch dent was $350, and the work took about an hour and a half. We quote each piece after seeing it, and we'll tell you honestly if it isn't a good candidate.